Concept
Crossdraft Spray Booth

Concept Crossdraft Spray Booth

The most versatile line of spray booths, CONCEPT spray booths are available in all four airflow models, multiple configurations, and with optional equipment designed to fit any shop, any size, anywhere.

With the CONCEPT spray booth line, you get your booth, your way, with no compromises. GFS incorporates exclusive technologies and innovative engineering into every CONCEPT booth for a single-skin spray booth with unequaled performance and quality.

Concept
Crossdraft Spray Booth

Standard Features:

Standard Cabin Specifications:

Internal: 14'w x 8' 9"h x 25'
External: 14' 4"w x 8'11.5"h x 28'5"l

• Horizontal spray booth airflow during operation
• Single skin panel construction
• Galvanized steel
• Heavy-duty filtered swing entrance door
• Large, solid back exhaust chamber
• High-efficiency intake and exhaust filtration
• 24" exhaust fan and 3hp exhaust motor
• (8) 4-tube color corrected T-8 light fixtures
• Inside-accessible ETL-listed light fixtures
• Side access door with obervation window (1) per Standard cabin
• Airflow Specifications:
- 8,550 SCFM and 75 FPM

BT1200-RC Recirculating
•Standard with Downdraft model

Concept Spray Booth Heater

BT1200 High-Efficiency Heat Groups:

Designed for indoor use
-10 hp Direct-drive intake motor
-7.5 hp Belt-drive exhaust motor
-34" Tube-axial exhaust fan
-12,000 CFM
-1.2 Million BTU direct-fire burner
-Auto pressure control

LOGIC Touch-screen Control Panel:

Easy-to-Use, fully programmable PLC control panel with SmartCure allows custom 'Heat vs. Time' cure cycles. Standard with Downdraft, upgrade available with BT1200 Heat Group for other models.

Concept Crossdraft
Proven airflow design

The Concept Crossdraft takes a popular and classic spray booth design and integrates energy-saving components to create a very economical paint-and-cure booth.

-Crossdraft airflow for spray and cure
-White pre-coated galvanized steel
-Rolled-edge panel construction
-Twelve 4-tube sidewall light fixtures, 120/277V
-Light wiring harness and limit switch
-One personnel access door 32-1/4"w x 7'8"h
-34" tube-axial exhaust fan
-5 hp exhaust motor, 12,000 CFM
-Exhaust-mounted Variable Frequency Drive
-Filter draft monitoring gauge
-Filtered entry doors with high-efficiency filters
-Rear exhaust box high-efficiency filters
-Optional exhaust yoke

Concept
Crossdraft Spray Booth

Optional AdvanceCure Acelerated Airflow System:

AdvanceCure Accelerated Airflow System is optional on all Concept models. Adding AdvanceCure to the interior of the booth vastly improves the productivity of the equipment. AdvanceCure introduces controlled turbulence into the paint booth during the flash-off and cure cycles to rapidly draw vapors out of the painted surfaces. This increased airflow dramatically reduces the amount of time required for each paint job, and in turn, increases the profitability of your body shop. AdvanceCure speeds curing of both solvent-based and waterborne paints, so you can be sure that your finishing operation will improve today, and well into the future.

Optional Cabin Equipment:

• Electrical control panel
• 34" exhaust fan and 5hp exhaust motor
• (10) 4-tube color corrected T-8 light fixtures
• Pressure balancing packages
• Air makeup unit
• Ductwork
• Airflow Specifications:
- 11, 400 SCFM and 100FPMs

Concept
Crossdraft Spray Booth

Code Compliance:

NFPA-33 Standard for spray application using flammable or combustible materials
NFPA-86 Standard for ovens and furnaces
NFPA-91 Standard for exhaust systems for air conveying of materials
NFPA-101 Life Safety Code
NFPA-70 National Electric Code
OSHA Safety and Health Standards (29 CFR 1910, 1910.107)
BOCA National Fire Prevention Code; National Building Code; National Mechanical Code
ICBO Uniform Fire Code Article 45
SBCCI Standard Fire Prevention Code
ICC International Building Code
ICC International Fire Code Chapter 15
This booth has been reviewed and approved by:
ETL Equipment Testing Laboratory report # 3049856 Cabin
All Fixtures are ETL approved for hazardous locations.
All light fixtures are accessible from the interior of the spray booth and conform to the provisions of N.F.P.A. 33.
Electrical components, such as motors, motor starters, disconnect switches and push buttons, are listed or approved for the Class and Division in which they are located. Motors UL recognized PRGYZ, Marathon Electric file E49747 (or equal), Glass used in the spray booth is tempered and meets and exceeds ANSI Z-97.1 standard. Conformance to all these requirements is dependent upon the manner in which the equipment is installed. The contractor will make certain that all the electrical wiring and conduit, piping, gas supply, roof penetrations, automatic fire penetrations, automatic fire protection systems, and the location of the equipment within the building also conforms to the cited codes and other references. Fire suppression system is NOT included with the standard booth but is required by NFPA-33.

Concept
Crossdraft Spray Booth

Click on Image to Download PDF Brochure